TriggerTech KC0E ACE Trigger System

Tooteteave

• The ACE Trigger System is designed for use with Glock Gen 1-5 pistols chambered in 9mm or .40 S&W.
• It is engineered to provide a smooth and consistent trigger pull, enhancing the overall shooting experience.

Paigaldusjuhised

• Ensure your firearm is unloaded and safe to work with.
• Järgige kõiki kasutusjuhendis kirjeldatud ettevaatusabinõusid.
• Consult a licensed gunsmith or contact TriggerTech for assistance if needed.
• Carefully install the ACE Trigger System according to the provided instructions.
• Test the functionality of the trigger system before using the firearm.

Kasutusjuhised

• When using the ACE Trigger System, always follow proper firearm safety protocols.
• Ensure that you are familiar with the handling of firearms and trigger components before installation.
• Any modifications should be done by a qualified professional.

Disclaimer, Limited Warranty, Satisfaction Guarante, Installation Instructions

HOIATUS: Failure to properly install your trigger and ensure proper safety functionality could result in an unsafe rearm. Read and follow all instructions. Contact TriggerTech or a licensed gunsmith for assistance.

TriggerTechi lahtiütlus
Improper handling, installation, storage and/or use of TriggerTech products and/or the firearm in which they are installed can cause death, serious injury, and/or property damage.
TriggerTechi tooted on mõeldud paigaldamiseks ja kasutamiseks ainult selles konkreetses tulirelvas, mille jaoks neid reklaamitakse. Ostja kohustus on kindlaks teha ühilduvus.
Päästiku järelturu käsitsemine ja paigaldamine võib hõlmata keerulisi protseduure ja eeldada tulirelvade käsitsemise alaseid teadmisi. Kui ostja või kasutaja ei ole tulirelvade käsitsemise ja päästikukomponentide vahetamisega tuttav või pole sellega piisavalt tuttav, siis ostja või kasutaja (edaspidi ühiselt ...
„Ostja“) peab lisateavet ja abi otsima relvameistrilt või muult kvalifitseeritud spetsialistilt.
By installing or using any purchased TriggerTech trigger product (“TT Product”), the Purchaser agrees to the following terms and conditions:

1. The Purchaser will abide by all applicable firearm safety laws, protocols, and regulations in force in the jurisdiction where the TT Product is handled, installed, stored and/or used;
2. The Purchaser certifies that he/she is legally entitled to purchase and use the TT Product and the firearm in which it is to be installed, in the jurisdiction where the TT Product is purchased and used;
3. The Purchaser assumes responsibility for ensuring that any users of the TT Product comply with these terms and conditions and with all applicable firearms safety protocols and regulations when handling, installing, storing and/or operating the TT Product;
4. The Purchaser agrees to conduct a test for proper trigger fit and function, before each use of the TT Product, with the firearm in which it is installed in an unloaded condition. Never assume the TT Product works without testing it;
5. The Purchaser agrees to consistently use a trigger lock on the installed TT Product, together with any related safety mechanism on the firearm in which the TT Product is installed.
6. The Purchaser agrees to contact TriggerTech immediately in the event of any change or loss of trigger function.
7. Following installation, the Purchaser will not conduct any maintenance of the TT Product that requires disassembly of the TT Product, in whole or in part
8. In no event shall TriggerTech be liable for any direct, indirect, incidental, special, consequential, or punitive damages arising from loss of life, personal injury and/or property damage, in connection with the use or misuse of the TT product, or the firearm in which the TT Product is installed;
9. TriggerTech is not responsible for the acts or omissions of the Purchaser resulting from a lack of training or knowledge of firearms handling, or failure to properly implement such training and knowledge
10. The Purchaser assumes the risk and all liability for death, injury, and loss and damage to persons or property caused by use or installation inconsistent with TriggerTech’s instructions, negligent or intentional use or misuse of the TT Product, or the firearm in which the TT Product is installed.

TriggerTechi piiratud garantii

TriggerTech warrants to the original retail purchaser that this TriggerTech product will be free from manufacturing and handling defects for thirty days after the original sale of the product, and from manufacturing defects for the life of the product. This warranty only applies if this product was manufactured and sold by TriggerTech. This warranty excludes conditions caused by excessive wear and tear, aggressive handling, unreasonable use, modifications, alterations, tampväärkasutus, ebaõige paigaldamine või muud TriggerTechi kontrolli alt väljas olevad tegurid. Toote mis tahes viisil muutmine TÜHISTAB selle garantii. See piiratud garantii ei laiene tulevasele jõudlusele.
Ühelgi TriggerTechi esindajal, turustajal ega edasimüüjal ei ole õigust võtta tootega seoses mingeid muid kohustusi ega vastutust ega muuta käesoleva garantii tingimusi.
KÕIK MUUD GARANTIID PEALE SIIN MÄÄRATUD ON KEELATUD, SEALHULGAS KAUDSETEST GARANTIIDEST KAUBASTATAVUSE JA KINDLAKS OTSTARBEKS SOBIVUSE KOHTA, KOHALDATAVA SEADUSEGA LUBATUD ULATUSES. KÕIK VASTUTUS JUHUSLIKE, KARISTUSLIKE, ERILISTE VÕI TEGEVUSEST TULENEVATE KAHJUDE EEST KEELATAKSE SELGESÕNALISELT KOHALDATAVA SEADUSEGA LUBATUD ULATUSES.
TriggerTech does not assume any liability arising from loss of life, personal injury and/or property damage in connection with the use, misuse or modification of the TT product, or the firearm in which the TT Product is installed.
Garantiiküsimustega tegeleb otse TriggerTech, mitte meie edasimüüjate võrgustik. Garantiikaitse saamiseks võtke meiega otse ühendust aadressil
number/website below for a return authorization. The product alleged to be defective must be returned to TriggerTech for inspection. The cost of shipping to us is the customer’s responsibility. Any products determined by TriggerTech to require warranty coverage will be replaced or repaired, at TriggerTech’s sole option.

Märkus. TriggerTechi päästiku paigaldamine võib tühistada teie tulirelva tootja garantii osaliselt või täielikult, seega kontrollige enne päästiku paigaldamist tulirelva tootjaga, kas paigaldamine mõjutab teie tulirelva garantiid.
TriggerTechi rahulolugarantii
TriggerTech triggers have distinctively less creep than competitors’ products. While most shooters view this as a benefit, some may not enjoy the distinct, crisp feeling of a TriggerTech trigger. If you are the original purchaser and are not satisfied with the zero-creep break of your TriggerTech trigger, you may return it to TriggerTech within thirty (30) days of purchase, in the original packaging and with proof of purchase. Provided the trigger is undamaged, TriggerTech will refund the purchase price.
LAHTIÜTLEMINE: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. or GLOCK Ges.mbH. TriggerTech is not affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.mbH. The use of “GLOCK” in this document is merely to outline how to install the TriggerTech Ace Trigger System in GLOCK pistols. For genuine GLOCK, Inc. and GLOCK Ges.mbH products and parts, visit www.glock.com.

TriggerTech ACE päästikusüsteem Glockile

Detailed instructions, FAQ and videos: www.triggertech.com

Ühilduvus

• TriggerTech’s ACE Trigger System for Glock is compatible with all standard frame Generations of Glocks (1-5) in 9mm & .40 S&W. The models are: G17, 17L, 19, 19x, 22, 23, 24, 26, 34, 35, 45, 47.
• Gen 5 Glockide puhul tuleb raamil olev väike sakk eemaldada.
• Mõnede raamide tolerantsi kõikumiste tõttu võib sertifitseeritud relvasepp nõuda paigaldamist ja kinnitamist, et tagada kangi ohutuse nõuetekohane toimimine.
• TriggerTech has not verified compatibility with clone frames.

Unload your firearm and disassemble it

• Read the TriggerTech Disclaimer and TriggerTech Lifetime Warranty prior to installation and use.
• Visually and physically confirm the firearm is unloaded while keeping the muzzle pointed in a safe direction at all times.
• Eemaldage slaid.

Remove the existing trigger

• Eemaldage eesmine(d) päästiktihvt(id) ja seejärel tagumine päästiktihvt.
• Remove the barrel lug and then the slide stop.

• Tõstke päästik üles ja püstolist välja.

Install the TriggerTech Disconnect Module

• Eemaldage tehase tagaplaat, vajutades kaasasoleva tihvtitööriista abil lööknõela vahehülsi alla ja seejärel eemaldage kelgu katteplaat.
• Paigaldage TriggerTechi lahtiühendamismoodul, vajutades tihvtitööriista abil lööknõela vahehülssi ja seejärel väljatõmbevarda, libistades lahtiühendamismoodulit üles ja oma kohale.
• Kui tagaplaat on paigas ja seda ei saa enam välja libistada, peaks kostma klõps.

Märkus. REQUIRED Gen 5 modification

• Gen 5 Glocks have a small plastic tab at the back of the frame. It must be removed for the ACE Trigger System to operate. The firearm WILL NOT be able to function unless the tab is removed.
• Use an edged tool to carefully cut the tab flush with the frame.

Install TriggerTech ACE Trigger System

• Carefully mount the transfer bar from the lever module into the slot of the sear module. The two parts should nest easily without using any force.
• Insert the lever module first, followed by the rear module, into the frame.
• Paigaldage kelgupeataja ja silindri klamber tagasi.
• Paigaldage tihvtid vastavatesse aukudesse tagasi.

Safety lever function verification

• Veenduge, et teie turvahoob töötab korralikult. Veenduge visuaalselt, et teie päästikuhoova turvahoob vastab igas režiimis allolevatele joonistele.

Ohutus on tagatud

• If you apply a force at the top of the lever (where it meets the frame using the pin tool), the safety stop should contact the frame and prevent the gun from firing.

Ohutus välja lülitatud

• If you apply your finger to the trigger normally and start to press the trigger, the safety stop should clear the frame without interference.

Vallandatud

• Kui tõmbate läbi seina ja kuulete rõngaspoldi vabanemist, peaks üleliikumise piiraja raami puudutama.

Fit to frame corrective action

• Mõnel juhul võib raami tolerantsi kõikumiste tõttu hoova kaitse liigselt häirida ja hoob võib vajutamisel kleepuda või olla terav. Esimene samm on lähtestamiskäigu reguleerimine.
• Sellisel juhul vajate päästiku raamile paigaldamiseks Glocki sertifitseeritud soomusmeistri abi.
• To adjust the trigger reset position remove material from this tab using an abrasive tool. Only remove a small amount between fitting trials to mitigate lever-to-frame interference.

• Kui kleepumine püsib, peaks väikese koguse materjali eemaldamine ohutuspeatajast kleepumisprobleemi leevendama.
• Kangi ohutuse raamile sobivuse reguleerimiseks eemaldage materjali väikeste sammudega, kasutades file või abrasiivset tööriista näidatud hoova ohutuspeatajal olevate katsetuste vahel. Eemaldage ainult vajalik materjal hoova sujuva toimimise tagamiseks.

• Kui probleem püsib, võtke lisateabe saamiseks ühendust TriggerTechi klienditeenindusega aadressil tugi@triggertech.com või kvalifitseeritud relvameister.
• If the issue is resolved, then proceed with the function checks in Step 7 to verify that the lever safety is performing correctly.
• HOIATUS: Do not attempt Step 6 without the assistance of a Glock Certified Armorer.
• HOIATUS: Raami võimalike tolerantside kõikumiste tõttu on võimalik, et kangi kaitseriiv hõõrub liigselt või ei tööta üldse. ÄRGE KASUTAGE ACE päästikusüsteemi, kui kangi kaitseriiv ei tööta korralikult.

Funktsiooni kontroll

• Prior to using your firearm, perform the following tests without ammunition and confirm your firearm is unloaded and pointed in a safe direction at all times to confirm your installation was done correctly. If your pistol fails any of these tests, do not use your pistol and contact TriggerTech Support or take your pistol to a certified Glock Amorer.
• Tehke järgmised katsed, kui slaid on raamist eemaldatud:
• Lööjaküünal: Hoidke lööjaküünalt sõrmeotsaga allavajutatult ja raputage kelku jõuliselt otsast lõpuni. Peaksite kuulma, kuidas lööjaküünal lööjaküünal vabalt liigub. Veenduge, et lahtiühendamismoodul ei sega lööjaküünalt.
• Kontrollige päästiku hoova kaitset, tõstes lööknõela kaitsehooba üles. Päästiku hoova kaitse peaks blokeerima ülekandevarda nii, et kõrvetus ei kukuks alla enne, kui päästikuhoob on aktiveeritud.

HOIATUS: Raami võimalike tolerantside kõikumiste tõttu on võimalik, et kangi kaitseriiv hõõrub liigselt või ei tööta üldse. ÄRGE KASUTAGE ACE päästikusüsteemi, kui kangi kaitseriiv ei tööta korralikult.

• Test reset – pull and hold the trigger, push down the transfer bar and you should hear an audible click which indicates reset has occurred. Release the trigger lever and the transfer bar should return up to its starting position.

• Firing Pin Safety Test: Hold the slide and pull the lug of the firing pin all the way to the rear of the slide and then ease it forward until it stops in contact with the firing pin safety. Then press the lug of the firing pin forward with your forefinger using moderate force. The firing pin must not move forward past the firing pin safety, and must not protrude from the breech face of the slide. If the firing pin safety fails to keep the firing pin from moving forward. DO NOT LOAD OR FIRE YOUR PISTOL. Instead, have it inspected and repaired by a Glock Certified Armorer.
• Firing Pin: Hold the slide with the muzzle end downward, and press the firing pin safety into the slide with your fingertip. The firing pin should move downward, and the tip of the firing pin should protrude from the breech face. (Note: On brand new pistols, you may need to apply light downward pressure to the rear of the firing pin lug with your finger to assist the firing pin in moving downward).
• Inspect the ejector to ensure that it is intact.

Tehke järgmised katsed täielikult kokkupandud tulirelvaga.

• Cycle the slide to reset the trigger, and press the trigger. You should hear and feel the firing pin release.
• Cycle the slide, press and hold the trigger to the rear. While continuing to hold the trigger to the rear, cycle the slide, then release the trigger. The trigger should reset. Press the trigger to ensure the firing pin releases.
• Insert an EMPTY magazine into the pistol. Pull the slide fully to the rear; the slide should lock open.
• Veenduge, et päästihoob liigub vabalt ega puutu päästikukaitset. Klõpsatust ei tohiks kuulda.
• Once 7a-j have been successfully passed without ammunition, you can begin using ammunition at a range. Start with one round and slowly increase the number of live rounds in your magazine.

Tõstke üles, murdke raskus ja lähtestage tunnetuse reguleerimine

Users can tune the take up, break weight and reset feel of the trigger to their individual preference. Included with your TriggerTech ACE Trigger System are three springs: a heavy take-up spring (pre-installed), a light take-up spring and a light plunger spring. Users can use different combinations of springs to find the right pull weight range and feel, then use our patented CLKR Technology™ to dial in their own setting.

Teie TriggerTechi päästik on seatud reklaamitud tõmbetugevuse vahemiku keskele, paigaldades raske vastuvõtuvedru.
HOIATUS: It is recommended to operate your trigger at or above factory settings. Exercise caution when adjusting your pull weight and repeat Step 7 prior to using live ammunition.

Pull weight adjustment – lever/take-up spring

Your TriggerTech ACE Trigger System is pre-installed with the heavy take-up spring (silver), with a light take-up spring
(gold) included in the packaging. To change the spring in the lever, follow the steps below:

• Eemaldage hoob, vajutades tihvti välja kaasasoleva hoova tihvti tööriistaga.
• Eemaldage vedru.
• Insert the new spring into the spring lever pocket of the trigger lever and engage the spring protrusion in the transfer bar
• Paigaldage tihvt uuesti.

Tõmbejõu reguleerimine – kolvi vedru

To change your factory plunger spring to the included TriggerTech ACE Trigger System light plunger spring (black):

• Eemaldage tagaplaat (vt samm 3a)
• Eemaldage tõmbevarda ja löökmehhanismi komplekt.
• Ekstraktori eemaldamiseks vajutage kolbi alla. See kukub kelgust välja. Ka kolb kukub välja.
• Eemaldage kolvis olev vedru.
• Replace it with the ACE Trigger System plunger spring and press it firmly into the plunger so it is set in place and won’t fall out on its own.
• Reinstall the plunger and apply pressure on it inward to the slide while you put the extractor back in. Then reinstall the extension rod and striker assembly.
• Paigaldage tagaplaat uuesti.

Tõmmamisraskuse reguleerimise hoiatus

• TÄHTIS: Your TriggerTech ACE Trigger System allows you to adjust your trigger pull weight. The set screw is located on top of the Sear Module and is set to near the middle of the advertised pull weight range. To adjust the pull weight, insert the supplied 5/64” Allen wrench. To increase pull weight, turn the set screw clockwise. Do not adjust your Sear Module more than 8 full rotations from the lowest pull weight.
• HOIATUS: It is recommended to operate your trigger at, or above factory settings. Exercise caution when adjusting your pull weight and repeat Step 7 prior to using live ammunition.
• The TriggerTech ACE Trigger System has an adjustable take-up, break weight, and reset feel. The factory setting is near the middle of the advertised range. There is such a thing as a trigger that is too light to be considered safe. This weight will change depending on the specifics of the firearm, the experience of the shooter and the intended use case (how the gun and all of its components are operated/handled). TriggerTech strongly recommends that you get some trigger time on your TriggerTech trigger before adjusting the break weight below the factory setting (a trigger set at 4.0 lbs is safer than a trigger set at 2.5 lbs). As you reduce the pull weight of a TriggerTech ACE Trigger System, you are reducing the amount of spring tension in the trigger, and it is possible that you may reach a point where the trigger in a specific firearm is not safe for the intended use case and/or the shooter.
• The trigger’s pull weight should not suddenly change on its own. If it does, stop using it immediately and contact TriggerTech Support.
• Laskjatele tuletatakse meelde, et nad peaksid alati järgima NRA relvaohutuseeskirju.

TriggerTechi tõmberaskuste juhend

Hooldus Puhastamine

Your TriggerTech trigger is designed to operate maintenance-free and lubricant-free. It is recommended that you minimize the amount of oil and gun cleaning products that get in contact with the trigger.
Soovitame püstolijääkide hulka minimaalsena hoida.
Kui arvate, et teie päästik ei tööta saastumise tõttu korralikult, soovitame teil järgida järgmisi samme:

1. Veenduge, et teie tulirelv on laadimata.
2. Tõmba kelk üles ja tulista tulirelvaga korduvalt kuivalt.
3. If Step 2 is unsuccessful, remove your TriggerTech trigger from the frame and you can try to clean with compressed air and/or a grease-cutting agent that does not leave residue. We recommend lighter fluid, letting it dry, and blowing out the trigger with compressed air. Follow the TriggerTech Installation Instructions when reinstalling your trigger.
4. If Step 3 is unsuccessful, we do NOT recommend opening your trigger housing and suggest you contact TriggerTech and arrange to have your trigger serviced. Note: breaking the “void if removed” will indicate that you have opened your trigger and may void the Limited Warranty.

Kas teil on küsimusi?

• 1-888-795-1485 Tugi@TriggerTech.com. www.TriggerTech.com

KKK

• Q: What should I do if I encounter any issues with the ACE Trigger System?
  • A: If you experience any issues with the product, please contact TriggerTech directly for assistance. Do not attempt to modify or repair the trigger system yourself to avoid potential safety hazards.
• K: Kas TriggerTechi päästiku paigaldamine tühistab minu tulirelva tootja garantii?
  • A: Installation of aftermarket triggers may void part or all of your firearm manufacturer’s warranty. It is recommended to check with the firearm manufacturer before installing the trigger system to understand the impact on your warranty coverage.

Dokumendid / Ressursid

TriggerTech KC0E ACE Trigger System [pdfKasutusjuhend 2025, KC0E ACE Trigger System, KC0E ACE, Trigger System, System

Viited

• Kasutusjuhend