Synapse CSEN1 Combo Sensor Controller Installation Guide

PAIGALDAMISJUHEND
CSEN1

CSEN1 Combo Sensor Controller

Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)

KIRJELDUS

The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.

SPETSIFIKATSIOONID

• Raadiosagedus: 2.4 GHz (IEEE 802.15.4)
• RF-edastuse väljundvõimsus: +20dBM
• Töötemperatuur: -40° kuni +70°C
• Tööniiskus: 10 kuni 95%, mittekondenseeruv
• IP66 kaitseklass
• Mõõdud: 3.1 tolli D x 1.6 tolli K (80 mm D x 42 mm K)
• Input Power: 12-24VDC, 35mA max, 840mW
• Juhtimise eesmärk: käitamine
• Environmental: Indoor/Outdoor
• Reostusaste: 3
• Rated Impulse Voltage: 330 V.

DISAIN KAALUTUSED

Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage 10V alalisvoolust.

• Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
• Võimalusel suunake hämardamise juhtmed vahelduvvooluliinidest eemale.
• Maksimaalselt 4 DALI-2/D4i LED-draiverit kontrolleri kohta, suurema suhte vajaduse korral konsulteerige Synapse'i toega.
• Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
• Ärge kinnitage jahutusradiaatorile ega LED-draiverile.

MÄRKUS. LED-draiver peab toetama funktsiooni DIM to OFF.
HOIATUSED JA HOIATUSED

• TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
• The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
• Nende juhiste ja hoiatuste eiramine võib garantii tühistada.
• This product must be installed in accordance with national, state, and local electrical codes and requirements.
• If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.

ZHAGA RAAMATU 18 PISKKONNA JUHTMETE ANDMED

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:

• 12-24VDC POWER: Brown
• Common Ground/DALI-: Pink with White Stripe
• DALI+/DIM+: Violet with White Stripe
• Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length

JOONIS 1

PAIGALDAMISJUHEND

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!

1. Vajadusel eemaldage kinnituskork või valgustuse juhtseadis, mis on parasjagu armatuuri pistikupesasse paigaldatud.
2. Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
3. After alignment, push until the CSEN1 is fully seated within the receptacle.
4. While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)

Märkus. Õigeks toimimiseks veenduge, et kontroller on täielikult pessa sisestatud ja lukustatud asendisse keeratud.
Hoiatus: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
JOONIS 2

STATUS LEDid

REGULEERIV TEAVE JA SERTIFIKATSIOONID
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada (IC) sertifikaadid: see digitaalseade ei ületa Kanada sideministeeriumi raadiohäirete eeskirjades sätestatud digitaalseadmete raadiomüra emissiooni B-klassi piirnorme.
FCC sertifikaadid ja regulatiivne teave (ainult USA)
FCC osa 15 klass B: see seade vastab FCC reeglite osale 15. Töötamisel kehtivad kaks järgmist tingimust: (1) need seadmed ei tohi põhjustada kahjulikke häireid ja (2) need seadmed peavad vastu võtma kõik vastuvõetud häired, sealhulgas häired, mis võivad põhjustada kahjulikku tööd.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:

• Osa 15, B-alajagu, B-klassi seadmete jaoks
• FCC 96-208, kuna see kehtib B-klassi personaalarvutite ja välisseadmete kohta
• Seda toodet on testitud FCC reeglite kohaselt sertifitseeritud välises katselaboris ja see vastab FCC 15. osa heitkoguste piirnormidele. Dokumentatsioon on sisse lülitatud file ja saadaval ettevõttest Synapse Wireless, Inc.

Kui selle toote korpuse sees oleva mooduli FCC ID ei ole teise seadme sisse paigaldamisel nähtav, peab selle seadme välisküljel, millesse see toode on paigaldatud, olema ka silt, mis viitab kaasasoleva mooduli FCC ID-le. Muudatused (FCC 15.21):
Selle seadme muudatused või modifikatsioonid, mida Synapse Wireless, Inc. pole sõnaselgelt heaks kiitnud, võivad tühistada kasutaja volitused seda seadet kasutada.
Patenteeritud – virtuaalne märgistus kl https://www.synapsewireless.com/about/patents
Lisateabe saamiseks külastage: synapsewireless.com

SERTIFIKATSIOONID

DALI-2 sertifitseeritud rakenduskontroller