ORTECH ERV-SC-1 Screen Controller

Tehnilised andmed

• Toote nimetus: ERV EKRANI KONTROLLER ERV-SC-1
• Paigaldus: seinale paigaldatav
• Features: Ultra-thin wired controller, OCA-bonded capacitive touch screen, Adjustable brightness
• Power Source: Powered by ERV, no battery required

TÄHELEPANU

Wall-Mounted, Screen Controller for Energy Recovery Ventilators

• Ultra-thin wired controller
• OCA bonded capacitive touch screen Easy installation
• Powered by ERV, no battery required
• Reguleeritav heledus
• Lai viewnurgaga

HOIATUS

TULEKAHJU, ELEKTRILÖÖGI VÕI INIMESTE VIGASTAMISE OHTU VÄHENDAMISEKS JÄRGI JÄRGMIST:

• Kasutage seda seadet ainult tootja poolt ettenähtud viisil.
• Before servicing or cleaning unit, switch power off.
• Paigaldustöid ja elektrijuhtmeid peab tegema kvalifitseeritud isik(ud) vastavalt kõikidele kehtivatele reeglitele ja standarditele, sealhulgas tulekindlusega ehitusnormidele ja standarditele.
• Seina lõikamisel või puurimisel ärge kahjustage elektrijuhtmeid ja muid peidetud kommunaalseadmeid.

ETTEVAATUST

• Read all instructions before installing or using this unit.
• To reduce the risk of fire, remove any shipping material that may be present inside the unit.
• Kontrollige kõiki juhtmeühendusi veendumaks, et need vastavad õigele vooluvõimsusele.
• After connecting the ERV-SC-1, please keep the knobs on the control board at the factory settings (100CFM).

JUHTMESTIKU SKEEM

RIISTVARA SISU

MONTEERIMISJUHEND

1. Using straight screwdriver, pry off the bracket of the ERV-SC-1.
2. Install the bracket to the wall using two screws. Ensure the bracket is oriented correctly (up).
3. Connect wire to terminals on the ERV-SC-1, note which wire color has been chosen for each terminal.
4. Install the ERV-SC-1 to the bracket without using screws, the ERV-SC-1 can be fixed by the tabs.Soovitame iga terminali jaoks kasutada järgmisi juhtmevärve:
   • Red for “12V”,
   • Yellow for “A”,
   • Green for “B”,
   • Black for “0V”.
5. Connect wires to terminals on the unit.
   Note: Match the wire color with the right terminal, red wire to terminal “12V”, yellow wire to terminal “A”, green wire to terminal “B”, black wire to terminal “0V”.
6. After connecting the ERV-SC-1, please keep the knobs on the control board at the factory settings (100CFM).

ETTEVAATUST

Please connect according to the requirements, do not connect incorrectly, otherwise it may cause electrical damage.

DISPLAY CONTROLLER OPERATION

OPERATSIOONID

1. Press the ON button to let the unit ventilate continuously.
   • a. W hen the outdoor temperature is higher than -10°C, the unit will run continuously.
   • b . When the outdoor temperature is less than -10°C, the unit run as per the Temperature Sensor Operation tables in manual.
2. Press the ECO button to set the running time per hour. The unit will run as follows:
   • 10min: run 5min, st op 25min;
   • 15min: run 5min, st op 15min;
   • 2 0min: run 5min, stop 10min;
   • 25-5 5min: run as per the set time once per hour.
3. When the outdoor temperature and humidity is out of OA limit of temperature and humidity range, the unit will run as per a 5 min on/ 15 min off cycle. OA limit of temperature and humidity setting range is as follows:
   • Temperature High: 68-113°F
   • Temperature Low: 14-50°F
   • Humidi ty High: 45-99%
   • Humidi ty Low: 10-40%

VEAOTSING

ETTEVAATUST

In addition to the display, the unit also provides alarm reminders. The alarm buzzer sounds every 4 hours, lasting for 5 seconds each time.

• During the FILTER CHECK OR MAINTENANCE alarm, there will be a popup page showing: Pause, Continue or Reset.
• All alarms can be exited by pressing the return button to go back to the main interface. And by clicking the “ ” icon, the alarm interface can be displayed again.
• If the screen is not powered, please check the ERV unit is powered on, the display is powered by the ERV unit.

ORTECH jätab endale õiguse igal ajal ilma ette teatamata muuta oma toote mis tahes või kõiki omadusi, disaini, komponente ja spetsifikatsioone, et vastata turu muutustele.

More Imfo

• www.ortechindustries.ca
• 1.888.543.6473
• 13376 Comber Way, Surrey, BC V3W 5V9
• 205 Summerlea Road, Bramptonni, Ontario
• info@ortechindustries.com
• 604.543.6473

KKK

K: Mida peaksin tegema, kui pärast paigaldamist tekib elektriprobleeme?

A: If you encounter any electrical issues after installation, immediately switch off power and consult a qualified professional to inspect and resolve the problem.

Q: Can I adjust the brightness of the screen on the ERV-SC-1?

A: Yes, the ERV-SC-1 features adjustable brightness to suit your preferences.

Dokumendid / Ressursid

ORTECH ERV-SC-1 Screen Controller [pdfKasutusjuhend ERV-SC-1, ERV-SC-1 Screen Controller, Screen Controller, Controller

Viited

• Kasutusjuhend