MATRIX GM167F 3 Stack Multi Gym

Tooteteave

Õige kasutamine

1. Ärge ületage treeningseadme kaalupiiranguid.
2. Vajadusel seadke ohutuspiirikud sobivale kõrgusele.
3. Vajadusel reguleerige istmepadjad, jalapadjad, jalapadjad, liikumisulatuse reguleerimine või mis tahes muud tüüpi reguleerimismehhanismid mugavasse algusasendisse. Veenduge, et reguleerimismehhanism oleks täielikult sisse lülitatud, et vältida tahtmatut liikumist ja vigastusi.
4. Istuge pingile (kui see on olemas) ja võtke treeninguks sobiv asend.
5. Treenige mitte rohkem raskustega, kui saate ohutult tõsta ja kontrollida.
6. Tehke harjutusi kontrollitud viisil.
7.  Viige raskus täielikult toetatud algasendisse.

Toote spetsifikatsioonid

Maksimaalne kasutaja kaal	159 kg / 350 naela
Maksimaalne treeningu kaal	91 kg / 200 naela
Toote kaal	592 kg / 1305 naela
Overall Dimensions(L x W x H)*	282 x 323 x 218 cm /111 x 127 x 86”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX strength equipment. Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals with wheelchairs.

Pöördemomendi väärtused

M12 Bolt (Nyloc Nut & Flow drill)	135 Nm / 100 jalga-naela
M10 Bolt (Nyloc Nut & Flow drill)	77 Nm / 57 jalga-naela
M8 poldid	25 Nm / 18 jalga-naela
M8 Plastik	15 Nm / 11 jalga-naela
M6 poldid	51 Nm / 11 jalga-naela
Padja poldid	10 Nm / 7 jalga-naela

Paigaldamine

1. STABIILNE JA TASANDIL PINNAD: MATRIX treeningvarustus tuleb paigaldada stabiilsele alusele ja korralikult tasandada.
2. SEADMETE KINNITAMINE: Tootja soovitab kõik statsionaarsed MATRIX-i tugevusseadmed põranda külge kinnitada, et seadmed stabiliseerida ja vältida kõikumist või ümberkukkumist. Seda peab tegema litsentseeritud töövõtja.
3. Ärge mingil juhul libistage seadet mööda põrandat ümberkukkumisohu tõttu. Kasutage OSHA soovitatud õigeid materjalide käsitsemise tehnikaid ja seadmeid.

Kõik kinnituspunktid peavad taluma 750 naela. (3.3 kN) väljatõmbejõud.

Hooldus

1. ÄRGE kasutage seadmeid, mis on kahjustatud või millel on kulunud või katkised osad. Kasutage ainult teie riigi kohaliku MATRIX-i edasimüüja tarnitud varuosasid.
2. HOOLDAGE SILTID JA NIMESILTID: Ärge eemaldage silte mingil põhjusel. Need sisaldavad olulist teavet. Kui see pole loetav või puudub, võtke asendamiseks ühendust MATRIX-i edasimüüjaga.
3. HOOLDAGE KÕIK SEADMED: ennetav hooldus on seadmete sujuva töö ja ka teie vastutuse minimeerimise võti. Seadmeid tuleb regulaarselt kontrollida.
4. Veenduge, et kõik kohandusi tegevad või mis tahes hooldust või remonti teostavad isikud on selleks kvalifitseeritud. MATRIX edasimüüjad pakuvad meie ettevõttes soovi korral teenindus- ja hoolduskoolitust.

Hooldus Meelespea

Clean Upholstery (¹)	Igapäevane
Inspect Cables (²)	Igapäevane
Puhastage juhtvardad	Igakuine
Kontrollige riistvara	Igakuine
Kontrollige raami	Bi-Annualy
Puhas masin	Nagu vaja
Clean Grips (¹)	Nagu vaja
Lubricate Guide Rods (³)	Nagu vaja

1. Upholstery & grips should be cleaned with a mild soap and water or a non-ammonia based cleaner.
2. Cables should be inspected for cracks or frays and immediately replaced if present. If excessive slack exists the cable should be tightened without lifting the head plate.
3. Juhtvardaid tuleks määrida teflonipõhise määrdeainega. Kandke määrdeaine puuvillasele lapile ja seejärel kandke juhtvardad üles ja alla.

Inspect Cables (Weekly)
It is important for a facility to check cable conditions weekly.

Fractures:
Casing can crack or fracture under strains during use. Any crack in the casing merits cable replacement even if no wire rope is exposed. Be especially observant for fractures near the components on the cable assembly.

Twisting/Binding:
Inspect casing to ensure wire rope is not twisting within its casing. Any sign of the cable twisting should be replaced immediately.

Bulging:
Internal wire rope strands can break within and coil causing a bulge to appear. Cable should retain same outside diameter throughout.

Frayed/Exposed Wire:
Any exposed wire rope protruding through the casing or at either end.

Flattened:
A section of cable is compressed and will not retain its shape (outside diameter).

Kõver:
Cable has ‘kink’ and prohibits cable from laying straight. Wire rope may be unraveling beneath casing and is compromised warranting replacement.

Ends Separating:
Watch for component end of cable to pull away from cable assembly – look for exposed wire rope. Often times the oil from inside the cable jacket will start to leak out which can cause the cable to become brittle over time.

Tensioning Cables (As needed)
Cables can stretch over their life. It’s important to check for proper tension and inspect for damage. Without proper tension, users will lose some range of motion and excess wear to the cables can occur.

Checking Tension:

1. Unpin the weight stack pin from the stack.
2. From the midway point of the cable bolt and top of weight stack, use your finger to move the cable from side to side. You should see no more than ½” (13mm) of deflection (about the width of your finger) before the top weight plate starts to move or you feel resistance from the cable.
3. If you have more than ½” (13mm) of deflection, follow the tensioning procedure on the following pages.

Tensioning Procedure:

1. Unpin the weight stack pin from the stack.
2. Remove the cable bolt from the head plate adapter.
   A minimum of  (13mm) of the cable bolt must be engaged into the head plate adapter. Strength cable bolts vary in length. Remove the bolt and measure it. Install it so a minimum of h” (13mm) is engaged into head plate. Turn down as needed based on cable tension (deflection).
3. Turn down the cable bolt so ½” (13mm) of the bolt is engaged into the head plate adapter (see image to the right)
4. Check cable tension. If you have no more than ½” (13mm) deflection the cable is tensioning properly (see checking for proper tension procedure above)
   • If you have too much deflection, turn the cable bolt down a few turns and check tension again. Do this

Lubricating Guide Rods (Monthly)
Matrix Fitness requires PTFE based non-aerosol lubricants

Märkus. PTFE is Polytetrafluoroethylene (Teflon)

Menetlus:

1. With a clean rag, wipe the guide rods and top of the weight stack so they are free of dirt and dust.
2. Spray a different rag with the required lubricant and wipe up and down the guide rod gently.
3. Holding the lubricant bottle 1”-2” from the top weight plate bushings, spray a small amount of lubricant between the bushing and the guide rod. Allow the lubricant to run down the guide rod inside the weight stack.
4. Get on the unit and with a light weight, do a few reps. Listen for noise and feel for any friction. Repeat Step 3 and 4 as necessary.
5. Wipe any overspray off the top weight plate.

Inspect Hardware (Monthly)
As equipment settles to the floor after being relocated and general use, frame bolts may begin to loosen. If this is noticed, follow the below steps to secure the bolt. It is best to do this repair at the end of the day as the facility slows down as it may take 24 hours for the VibraTite to cure/set.

1. Loosen the bolt in question to expose the bolt threads.
2. Apply VibraTite red thread locker to the bolt threads.
3. Pingutage polt.

Checking Bearings (Monthly)
Bearings play a vital role in the functionality of moving parts. However, over time, these bearings are susceptible to wear and damage. Therefore, it is essential to regularly check for any signs of bearing damage. To assess bearing condition, utilize two senses: touch and hearing. By feeling and listening to the movement of the frame, you can detect potential issues with the bearings. If you suspect that a bearing is damaged, it is crucial to take immediate action and replace it promptly. By proactively monitoring and addressing bearing damage, you can ensure the smooth and efficient operation of the machine, prolonging its lifespan and reducing the risk of malfunctions.

Puhastamine
Machines should be regularly cleaned. Approved cleaning materials and information can be found in the guide Cleaners, Disinfectants, and Lubricants (NB-2401006) bulletin listed on Online Remedy and CSWeb.

Täiendav dokumentatsioon

• Online Remedy and CSWeb contains additional supplementation for Matrix products that have a wealth of information that may not be explicitly covered in this document.
• Cleaners, Disinfectants, and Lubricants (NB-2401006)
• Strength Cable and Belt Guide (NB-2401007)
• Cleaning and Maintenance Checklist – Strength (NB-2401008)
• Assembly and Installation Guidelines (NB-2401009)

Montaažijuhendid
Below are the assembly guides for each model. Assembly guides can also be found in each frame’s individual Owner’s Manual. Strength equipment must be secured to the floor after assembly is complete.

Leveling and Securing Strength Equipment

Nivelleerimine
Composite leveling shims can be used to help level equipment when the floor is not level. Another tip is to loosen your frame bolts and give the machine a shake if possible. This may adjust the frame pieces a bit allowing it to sit better on the floor.  Tighten all bolts once you are done.

Securing Strength Equipment
Matrix Fitness recommends that all stationary strength equipment be secured to the floor or wall to stabilize equipment and eliminate rocking or tipping over. Matrix requires specific pull-out force requirements shown below. Use a licensed contractor to ensure the required retention force is met.

All Flooring

• Each anchoring fastener must withstand 3.3 kN (750 LBS) pull-out force from the floor.
• Anchor the exercise equipment at all provided locations.
• Understand where all bolt-down points are located on the exercise equipment and mark the locations prior to drilling holes into the floor.

Wood/Tile/Rubber Over Concrete Sub-floor

• Understand the thickness of the flooring material. Add this height to the overall length of the anchoring fastener when selecting fastener length to ensure proper embedded depth into concrete flooring.

Frame Connections

• Any frame connection bolt should have VibraTite Red Gel applied to the threads during assembly or anytime the bolt is used to re-assemble a unit.
• M12 bolts should be torqued to 100 N-m if it is being used with anyloc nut.
• M12 bolts should be torqued to 100 N-m if it is being used in a rivnut. VibraTite Red Gel should be applied to the bolt threads after assembling the washer

Montaažijuhend

1. samm2. samm

3. samm

4. samm

5. samm

6. samm

7. samm

8. samm

Osade asendamine

Flat Pad Replacement

1. All flat plads on this unit have four bolts securing them to the base frame.
2. Access to the bolts securing the pad is gained from the underside.
3. Pad bolts should be torqued to 10 Nm / 7 ft-lbs.

Round Pad Replacement (Snap Ring)

1. This frame features two types of round pads: one secured by a snap ring, the other by a bolt.
2. Snap ring can be removed by a 12” snap ring pliers.
3. Remove the end cap and remove the pad from the frame, and then remove the two inserted end covers.
4. Reverse steps 1-3 to install the pad.

Round Pad Replacement (Bolted)

1. This frame features two types of round pads: one secured by a snap ring, the other by a bolt.
2. Remove the bolt securing the pad to the frame.
3. Remove the washer and disc securing the pad to the frame, and then remove the pad.
4. Remove the larger-disc (the one with the bigger hole positioned between the frame and pad) – note there are two different-sized discs on the frame.
5.  Reverse steps 1-4 to install the pad.

Cable Diagram – Multi-Position Press Cable Diagram – Leg Extension Curl

Cable Diagram – Lat Pulldown / Low Row
The Lat Pulldown / Low Row has two cables labeled as green and red in the diagram below.

Handlebar Foam Replacement

1. Remove the two set screws.
2. Remove the Grip Cap from the handlebar.
3. Remove the Grip from the frame, if necessary this can be carefully cut off.
4. Fully scour the frame underneath the foam, the frame where the foam should be placed needs to be entirely clean before the replacement is installed.
5. To ease installation, lightly apply warm soapy water to the inside of the handlebar foam and the corresponding section of the handlebar frame. This lubrication helps the foam grip slide smoothly into position.
6. Reinstall the grip cap and set screws.

Muudatuste logi

Versioon	Kuupäev	Nimi	Muuda
V1.0	5	Maxwell	Originaaldokument

Korduma kippuvad küsimused

• K: Mida peaksin tegema, kui seade on kahjustatud?
  A: Do not use the equipment if it is damaged. Contact your local MATRIX dealer for replacement parts.
• K: Kui sageli peaksin seadmeid hoolduseks kontrollima?
  A: Equipment should be inspected at regular intervals for preventative maintenance to ensure smooth operation and minimize liability.

Dokumendid / Ressursid

MATRIX GM167F 3 Stack Multi Gym [pdfKasutusjuhend GM167F, GM167F 3 Stack Multi Gym, GM167F, 3 Stack Multi Gym, Stack Multi Gym, Multi Gym

Viited

• Kasutusjuhend