FEIG MWD SBP R-silmusega radariskanner
Tehnilised andmed
- Toote nimetus: MWD SBP (R-silmus)
- Seadmete perekond: Radarskannerid
- Tootja: FEIG ELECTRONIC GmbH
- Kuupäev: 22.07.2025
SISSEJUHATUS
MWD SBP (R-Loop) Teaching a barrier boom with an accessory installed (hanging lattice/ climb protection/pendulum support) or a folding barrier boom
Device family: Radar scanners
Teema
- The MWD SBP offers the option of blanking out a hanging lattice, climb protection, or a pendulum support so that these are not detected as obstacles when the barrier is closing. If a boom accessory is used, it is essential to teach the movement of the barrier boom, including the boom accessory, to ensure that the barrier functions reliably! This process may also be necessary for folding barrier booms under certain circumstances.
Täpsemad seaded
- After completing the basic configuration of the radar scanner using the configuration assistant, you will then have the option of configuring advanced settings (menu point 7/7). Please select the step ‘Teach-in barrier boom’ from the submenu of the advanced configurations.
PALUN MÄRKUS
- Before starting the teach-in process, please ensure that you can control the barrier (OPEN/CLOSE) without being within the detection range of the radar scanner (key switch, hand-held transmitter, push button and cable, etc.). Optionally, you can also operate the barrier via the app by setting the corresponding outputs during the teaching process. This requires that the outputs have been wired accordingly.
- TÄHELEPANU: Safety is deactivated during the teach-in process! Please be sure to follow the instructions in the app.
To teach the boom accessory / folding boom, please proceed as follows:
- Create a way to control the barrier remotely (remote control, key switch, push button, cable, etc.)
- Open the barrier and leave the detection range of the radar scanner. Ideally, please stand behind the barrier. If necessary, it may be useful for the teach-in process to set the automatic closing time of the barrier to 5-10 seconds.
- Press ‘Start teach-in’ as soon as you have left the detection area. Be sure to follow the instructions in the app.!
- Close the barrier and then open it again. Repeat this process 2-3 times.
- End the learning process manually by tapping ‘End teach-in’.
The boom accessory / the folding barrier boom is no longer recognised as an obstacle. The status now updates to ‘Environment was teached-in’:
Samuti on olemas täpsemad sätted tõkkepuu poomi õpetamiseks. Täiustatud sätetes saate reguleerida radariskanneri tolerantsi poomi lisatarviku suhtes. Mida suurem on tolerants, seda suurem on ala, mis tõkkepuu poomi ümber varjatakse. Pange tähele, et kõrge tolerants vähendab ohutust! Millal on kõrge tolerants vajalik? Näiteksample, in strong winds that cause the barrier boom to sway randomly. However, this depends on the actual construction of the suspended lattice and its stability. For the best operation, the hanging lattice should be anchored to the barrier cabinet to reduce the horizontal movement in windy locations. The tolerance can be adjusted retrospectively without having to re-teach the barrier boom!
TÄHELEPANU
- Teaching in the barrier boom does not influence teaching the environment (menu point 6/7). These two teach-in processes must be carried out independently of each other. Furthermore, the configurations do not influence each other and have completely independent functions.
LISATEAVE
- FEIG ELECTRONIC GmbH
- Industriestraße 1a, 35781 Weilburg, Saksamaa
- Tel 06471/3109-0
KKK
K: Kas tõkkepuu poomi lisatarviku puhul on vaja õpetamisprotsessi korrata?
A: Yes, it is recommended to repeat the process 2-3 times to ensure accurate detection avoidance.
Q: Can the barrier boom accessory be taught in without a remote control?
A: No, a way to control the barrier remotely is needed for the teach-in process.
Dokumendid / Ressursid
 |
FEIG MWD SBP R-silmusega radariskanner [pdfJuhised MWD SBP R-Loop radariskanner, MWD SBP, R-Loop radariskanner, radariskanner, skanner |