Sensative Strips Drip Z-Wave 800 Water Leak & Temperature Sensor User Manual

1. Sissejuhatus

The Sensative Strips Drip Z-Wave 800 is an ultra-thin water leak and temperature sensor designed for smart home environments. It utilizes Z-Wave 800 technology to detect water leaks and monitor ambient temperatures, providing timely notifications to your Z-Wave controller. Its slim design allows for discreet placement in hard-to-reach areas, offering comprehensive monitoring for potential water damage or freezing conditions.

2. Ohutusalane teave

• Do not attempt to open or modify the sensor. Internal components are not user-serviceable.
• Keep the sensor away from direct heat sources or open flames.
• Ensure the sensor is installed in a location where it will not be physically damaged or submerged in water beyond its intended detection area.
• Dispose of the product and its battery according to local regulations. Do not incinerate.
• The provided magnet is for setup and reset purposes only. Keep it away from children.

3. Pakendi sisu

Veenduge, et teie pakett sisaldab järgmisi esemeid:

• Sensative Strips Drip Sensor
• Magnet (for setup)
• Kiirjuhend (see juhend)

Image: The Sensative Strips Drip sensor shown in its retail packaging, which includes the sensor and a small magnet.

4. Toote lõppview

The Sensative Strips Drip sensor is designed to be discreet and highly functional. It features an ultra-thin profile, allowing it to be placed in tight spaces where traditional sensors cannot fit. The sensor detects water presence across its length and reports ambient temperature.

Peamised omadused:

• Water Leak Detection: Senses water on most hard surfaces in 1-100% increments.
• Temperatuuri jälgimine: Reports ambient room temperature.
• Z-Wave 800 Technology: Extended wireless range and enhanced security (S2 and Secure Vault).
• Pikk aku tööiga: Up to 10 years with the built-in LiMnO2 battery.
• Universal Installation: Sobib kasutamiseks sise- ja välistingimustes.

5. Seadistamine

To set up your Sensative Strips Drip sensor, you will need a compatible Z-Wave controller or hub (sold separately). The sensor uses a magnet for activation and pairing.

5.1. Adding the Sensor to Your Z-Wave Network (Inclusion)

1. Prepare your Z-Wave Controller: Lülitage oma Z-Wave kontroller kaasamisrežiimi (sidumisrežiimi). Täpsemate juhiste saamiseks vaadake oma kontrolleri kasutusjuhendit.
2. Anduri aktiveerimine: Hold the provided magnet against the marked area on the sensor (usually indicated by a small indentation or symbol) for approximately 3 seconds, then remove it. The sensor's LED (if visible) may blink to indicate activation.
3. Confirm Inclusion: Your Z-Wave controller should detect and add the sensor. If successful, the controller will confirm the inclusion. The sensor may appear as multiple devices (e.g., leak sensor, temperature sensor, brightness sensor) depending on your controller's capabilities.
4. Smart Start (if supported): If your Z-Wave controller supports Smart Start, you can scan the QR code on the sensor or its packaging to automatically add it to your network.

Märkus. The timing of holding and removing the magnet is crucial. If inclusion fails, repeat the process. Some Z-Wave hubs may require several attempts due to timing sensitivities.

5.2. Paigutuse soovitused

The ultra-thin design allows for flexible placement. Consider areas prone to leaks or where temperature monitoring is critical.

• Valamute all (köögis, vannitoas)
• Tualettruumide taga
• Veesoojendite lähedal
• Under washing machines or dishwashers
• Keldrites või abiruumides
• Near pipes that may freeze

Image: The thin Sensative Strips Drip sensor positioned on the floor directly in front of a washing machine, illustrating discreet placement for leak detection.

Image: The Sensative Strips Drip sensor lying on the cabinet floor under a kitchen sink, near plumbing, demonstrating its use in a common leak-prone area.

6. Anduri kasutamine

Once successfully included in your Z-Wave network, the Strips Drip sensor will automatically begin monitoring for water leaks and reporting temperature data.

6.1. Water Leak Detection

When water comes into contact with the sensor's detection strip, it will trigger a leak alarm. This alarm is sent to your Z-Wave controller, which can then execute predefined actions (e.g., send notifications, activate a siren, shut off a water valve if integrated).

Märkus. The sensor's felt strip requires a few seconds to absorb water before triggering. This is normal operation.

6.2. Temperatuuri jälgimine

The sensor continuously monitors the ambient temperature in its vicinity and reports this data to your Z-Wave controller at regular intervals (default wake-up interval is 24 hours, but can be configured). You can use this information to monitor for extreme temperatures that could indicate freezing pipes or other issues.

Image: A smartphone screen displaying a smart home application interface, showing a "Water Leak Detected" alert and a temperature reading of 21°C, with the Sensative Strips Drip sensor visible under a sink in the background.

7. Hooldus

7.1. Aku tööiga

The Sensative Strips Drip sensor is equipped with a built-in LiMnO2 battery designed to last up to 10 years under normal operating conditions. The battery is not replaceable by the user. When the battery is low, the sensor will report its status to your Z-Wave controller.

7.2. Puhastamine

If the sensor becomes dirty, gently wipe it with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the sensor is dry before placing it back in its monitoring location.

8. Veaotsing

If you encounter issues with your Sensative Strips Drip sensor, refer to the following common problems and solutions:

9. Tehnilised andmed

10. Garantii ja tugi

For warranty information and technical support, please refer to the official Sensative website or contact their customer service directly. Keep your purchase receipt and product model number (11040321) handy for any inquiries.

Tootja: Tundlik

Websait: www.sensative.com