ROBOTIME puidust 3D elektrikitarri mudelikomplekt (mudel TG605K) kasutusjuhend

1. Sissejuhatus

This manual provides detailed instructions for assembling and maintaining your ROBOTIME Wooden 3D Electric Guitar Model Kit, model TG605K. This kit is designed to be a rewarding building experience, resulting in a detailed display model of an electric guitar and ampelujõulisem.

The kit consists of 140 precisely cut wooden pieces that interlock without the need for glue. Following the step-by-step instructions will guide you through the construction process.

Figure 1.1: Fully assembled ROBOTIME Wooden 3D Electric Guitar Model Kit.

2. Ohutusalane teave

• Vanuse soovitus: This kit is recommended for individuals 8 years and up. Adult supervision is advised for younger builders.
• Väikesed osad: The kit contains small parts which may pose a choking hazard. Keep out of reach of children under 3 years of age.
• Materjal: The puzzle pieces are made from wood. Handle with care to avoid splinters.
• Teravad servad: Some edges may be sharp after detaching pieces. Sanding may be required for a smooth finish.
• Liimi pole vaja: This model is designed for interlocking assembly without glue. For enhanced stability, especially for display, a small amount of wood glue can be used, but it is not required for basic assembly.

3. Seadistamine ja kokkupanek

3.1 Pakendi sisu

Enne kokkupaneku alustamist kontrollige, kas kõik komponendid on olemas. Pakend sisaldab tavaliselt järgmist:

• Pre-cut wooden sheets containing guitar and amplifier pieces.
• Instruction manual with numbered assembly steps.
• Small accessories (e.g., copper wire, sandpaper, cotton swab) as needed for specific details.

Figure 3.1: Typical contents of the model kit.

3.2 Monteerimisprotsess

The assembly process is designed to be straightforward, with pieces interlocking. No glue is required for the primary construction. Estimated assembly time is approximately 1.5 hours.

1. Ettevalmistus:
   • Carefully read through the entire instruction manual before starting.
   • Identify all wooden sheets and familiarize yourself with the numbered pieces.
   • Valmista ette puhas ja hästi valgustatud tööruum.
2. Tükkide eraldamine:
   • Gently press out each numbered piece from the wooden sheets. Avoid forcing pieces to prevent breakage.
   • If a piece is difficult to remove, use a small craft knife or the provided cotton swab to carefully cut the connecting points.
   • Use the provided sandpaper to smooth any rough edges or tabs after detaching.
3. Järgmised juhised:
   • Follow the step-by-step diagrams in the instruction manual precisely. Each step indicates which numbered pieces to use.
   • Ensure pieces are oriented correctly before interlocking.
   • Osade ühendamisel rakendage õrna ja ühtlast survet.
4. Komponentide ühendamine:
   • The guitar and amplifier are assembled separately and then connected to the display stand.
   • Pay close attention to the wiring details for the aesthetic connection between the guitar and ampelujõulisem.

Joonis 3.2: näitample assembly steps from the manual.

Figure 3.3: Hands demonstrating the assembly process.

4. Kuvamine ja interaktsioon

Once assembled, the ROBOTIME Electric Guitar Model is intended for display. It is not a functional musical instrument.

• Paigutus: Place the model on a stable, flat surface away from direct sunlight, excessive heat, or humidity to preserve the wood.
• Interaktsioon: While durable for display, avoid rough handling or dropping the model, as delicate parts may break.
• Kohandamine: The wooden surface can be painted or stained if desired, allowing for personalized decoration. Ensure any paints or finishes used are suitable for wood and non-toxic.

Figure 4.1: The assembled model displayed as a decorative item.

5. Hooldus

• Puhastamine: Dust the model regularly with a soft, dry cloth or a soft brush. Avoid using wet cloths or harsh cleaning agents.
• Hoiustamine: If disassembling for storage, do so carefully to avoid damaging the interlocking tabs. Store pieces in a dry, cool place.
• Remont: In case of minor breakage, wood glue can be used to reattach pieces.

6. Veaotsing

• Tükid, mis ei sobi:
  • Ensure the correct pieces are being used for the current step. Refer to the numbered diagrams.
  • Check for excess material or burrs on the tabs or slots. Use sandpaper to gently smooth these areas.
  • Kontrollige tükkide orientatsiooni.
• Pieces breaking during removal:
  • Apply gentle pressure when detaching pieces. If resistance is met, use a craft knife to carefully cut the small connecting points.
  • The kit often includes a few extra delicate parts. Refer to the parts list for duplicates.
• Mudel on ebastabiilne:
  • Ensure all interlocking connections are fully seated.
  • For added stability, especially if the model feels light, small weights can be added to the base (e.g., pennies with glue, as suggested by a user review).
  • While not required, a small amount of wood glue can be applied to critical joints for a more permanent and stable display.

7. Tehnilised andmed

Joonis 7.1: Kokkupandud toote mõõtmed.

8. Ametlik tootevideo

9. Garantii ja tugi

ROBOTIME is committed to customer satisfaction. If you encounter any issues during assembly, such as damaged or missing parts, please contact our customer service team.

• Võtke ühendust tugiteenusega: Refer to the contact information provided in your product packaging or visit the official ROBOTIME websait toetuse saamiseks.
• Reageerimisaeg: Our support team aims to respond to inquiries within 24 hours.