1. Sissejuhatus
This manual provides essential information for the safe and efficient operation of your Steinbach SPS 75-1 Filter Pump. This self-priming pump is designed for use with pool filter systems, capable of handling pools up to 33,000 liters. It features a robust 230 V/450 W motor and a pump capacity of 8,520 liters per hour (142 l/min).
Palun lugege see kasutusjuhend enne paigaldamist ja kasutamist hoolikalt läbi, et tagada seadme nõuetekohane kasutamine ning vältida kahjustumist või vigastusi.
2. Ohutusjuhised
Tulekahju, elektrilöögi või vigastuste ohu vähendamiseks järgige alati järgmisi ohutusnõudeid.
- Elektriohutus: Ensure the pump is connected to a properly grounded outlet. Do not operate the pump with a damaged power cord or plug. Disconnect power before performing any maintenance or service.
- Vee temperatuur: The pump is designed for a maximum water temperature of 35°C (95°F). Operating above this temperature can cause damage to the pump.
- Paigutus: Install the pump on a stable, level surface, away from direct sunlight and excessive moisture. Ensure adequate ventilation around the motor.
- Lapsed ja lemmikloomad: Hoidke lapsed ja lemmikloomad pumba töötamise ajal sellest eemal.
- Hooldus: Only perform maintenance as described in this manual. For complex repairs, consult a qualified technician.
3. Seadistamine
Follow these steps for proper installation of your filter pump.
- Lahtipakkimine: Carefully remove all components from the packaging. Inspect the pump for any signs of damage during transit.
- Paigutus: Position the pump as close to the pool as possible, ensuring it is below the water level for optimal self-priming. The pump should be on a firm, level surface to prevent vibration.
- Vooliku ühendused: Connect the pool hoses to the pump's inlet and outlet ports. The pump supports hose diameters of 32mm and 38mm. Ensure all connections are tight to prevent leaks and maintain prime.
Joonis 3.1: Lähivõte view of the pre-filter inlet with a hose connection, showing the clear cover and filter basket.
Figure 3.2: The pre-filter inlet without a hose attached, illustrating the threaded connection for secure fitting.
Figure 3.3: The pump's outlet connection with a hose securely fastened, ready for water discharge.
Figure 3.4: The pump's outlet port, showing the internal threading for hose attachment.
Figure 3.5: An overall perspective of the Steinbach SPS 75-1 Filter Pump, highlighting its compact design and key components.
- Pumba täitmine: As a self-priming pump, it will draw water once connected. However, for initial startup, it is recommended to fill the pre-filter housing with water to assist in faster priming.
- Elektriühendus: Plug the pump into a suitable 230V electrical outlet. Ensure the circuit is protected by a Residual Current Device (RCD) for safety.
4. Kasutusjuhised
Once installed, operating the pump is straightforward.
- Pumba käivitamine: Turn on the power supply to the pump. The pump will begin to draw water and circulate it through your filter system.
- Jälgimine: Observe the pump during its initial operation to ensure there are no leaks and that water is flowing correctly. The pump operates at approximately 70 dB.
- Pumba peatamine: Lülitage pumba toide välja.
- Tööaeg: The optimal run time for your pump depends on your pool size and usage. For a 33,000-liter pool, ensure sufficient daily filtration to maintain water clarity.
5. Hooldus
Regular maintenance ensures the longevity and efficiency of your pump.
- Eelfiltri puhastamine: The pump is equipped with a pre-filter to catch larger debris. Regularly inspect and clean the pre-filter basket. To do this, turn off the pump, disconnect power, unscrew the clear lid, remove the basket, clean it, and reassemble. Ensure the O-ring is properly seated for a watertight seal.
- Talvitumine: Before freezing temperatures, drain all water from the pump and hoses. Store the pump in a dry, frost-free location.
- Üldpuhastus: Keep the exterior of the pump clean and free from dirt and debris. Do not use harsh chemicals.
6. Veaotsing
If you encounter issues with your pump, refer to the following common problems and solutions.
| Probleem | Võimalik põhjus | Lahendus |
|---|---|---|
| Pump ei käivitu | Toiteallikas puudub Mootori ülekoormus Tööratas kinni kiilunud | Kontrollige toiteühendust ja kaitselülitit Allow motor to cool, check for obstructions Inspect and clear impeller |
| Madal veevool | Ummistunud eelfilter Õhuleke imemistorustikus Madal veetase basseinis | Clean pre-filter basket Kontrollige kõigi ühenduste tihedust Lisage basseini vett |
| Pump on mürarikas | Õhk süsteemis Vibratsioon Kulunud laagrid | Laske süsteemist õhk välja, kontrollige lekete olemasolu Ensure pump is on a stable surface Võtke ühendust kvalifitseeritud tehnikuga |
| Pump kaotab toitejõu | Õhuleke imemistorustikus Madal veetase Ummistunud eelfilter | Check all connections and O-rings Ensure adequate water level Clean pre-filter basket |
Kui probleem pärast nende lahenduste proovimist püsib, võtke ühendust klienditoe või kvalifitseeritud hooldustehnikuga.
7. Tehnilised andmed
Technical data for the Steinbach SPS 75-1 Filter Pump.
Figure 7.1: Product label detailing the pump's electrical and performance specifications.
Figure 7.2: Dimensional drawing of the pump, indicating height, width, and length.
| Parameeter | Väärtus |
|---|---|
| Mudeli number | 040920 |
| Voltage | 230 V |
| Võimsus | 450 W |
| Pumba võimsus | 8,520 l/h (142 l/min) |
| Max. Pump Height | 9 m |
| Ühenduse läbimõõt | 32/38 mm |
| Maksimaalne veetemperatuur | 35°C |
| Maksimaalne basseini suurus | 33,000 liitrit |
| Müra tase | u. 70 dB |
| Toote mõõtmed (P x L x K) | 45 x 20.5 x 25 cm |
| Kauba kaal | 6 kg |
| Materjal | Plastikust |
| Toiteallikas | Juhtmega elekter |
8. Garantii ja tugi
Specific warranty details for this product are not provided in this manual. Please refer to your purchase documentation or the manufacturer's official webgarantiiteabe sait.
For technical support, spare parts, or service inquiries, please contact Steinbach customer service through their official channels. Always provide your product model number (040920) and purchase date when seeking support.
