1. Sissejuhatus ja lõppview
The HP StorageWorks 60 Modular Smart Array (MSA60) is a 2U rack-mountable Serial Attached SCSI (SAS) disk drive array designed to support 3.5-inch Serial ATA (SATA) drives. This system provides a robust and scalable storage solution, offering data performance, availability, and storage density for various computing environments. This manual provides essential information for the proper installation, configuration, operation, and maintenance of your MSA60 unit.
Joonis 1: Esiosa view of the Hewlett Packard MSA60 Modular Smart Array. This image displays the front panel of the HP MSA60, featuring twelve 3.5-inch drive bays arranged in four columns of three. Each bay includes an indicator light, suggesting drive activity or status. The overall design is a standard rack-mountable 2U form factor.
2. Ohutusalane teave
Please read all safety instructions carefully before installing or operating the MSA60. Failure to follow these instructions may result in electric shock, fire, or damage to the equipment.
- Ensure the power supply is disconnected before performing any maintenance or installation procedures.
- Only use the power cords and adapters supplied or approved by Hewlett Packard.
- Install the unit in a well-ventilated area to prevent overheating.
- Ärge jätke seadet niiskuse ega äärmuslike temperatuuride kätte.
- Heavy equipment: Use proper lifting techniques or assistance when moving the unit.
3. Pakendi sisu
Verify that all components are present and undamaged upon unpacking. Contact your vendor immediately if any items are missing or damaged.
- HP MSA60 Modular Smart Array unit
- Racki paigalduskomplekt
- Toitejuhtmed (kogus võib piirkonniti erineda)
- SAS cables
- Dokumentatsioon (kiirjuhend, garantiiteave)
- Optional: 3.5-inch SATA hard drives (if purchased with the unit)
4. Seadistamine
4.1 Racki paigaldamine
- Attach the rack rails to the rack cabinet according to the instructions provided with the rack mounting kit.
- Carefully slide the MSA60 unit onto the installed rails until it clicks into place.
- Secure the unit to the rack using the provided screws.
4.2 Ajami paigaldamine
- Ensure the MSA60 is powered off and disconnected from power sources.
- Insert each 3.5-inch SATA hard drive into an available drive bay. Ensure the drive is fully seated and the latch mechanism engages.
- Korda kõigi soovitud draivide puhul.
4.3 Kaablid
- Connect the SAS cables from the MSA60 to the appropriate SAS controller ports on your server or host system.
- Connect the power cords to the MSA60 power supply units and then to a grounded power outlet.
5. Kasutusjuhised
5.1 Sisselülitamine
After all connections are secure, power on the MSA60 by ensuring the power outlets are active. The unit will typically power on automatically. Observe the indicator lights on the front panel for system status.
5.2 Esialgne konfiguratsioon
The MSA60 is managed through the SAS controller in your host server. Refer to your SAS controller's documentation for instructions on how to detect the array, configure logical drives (RAID levels), and allocate storage.
5.3 Ajami olekuindikaatorid
- Roheline (tahke): Drive is active and operating normally.
- Roheline (vilkuv): Drive activity (reading/writing data).
- Merevaikkollane (tahke): Drive fault or predictive failure.
- Väljas: Drive is not present or not powered.
6. Hooldus
6.1 Korralised ülevaatused
- Kontrollige perioodiliselt kõiki kaabliühendusi, et need oleksid kindlalt paigas.
- Monitor the status indicator lights on the front panel for any anomalies.
- Tagage seadme ümber piisav õhuvool, et vältida ülekuumenemist.
6.2 Ajami vahetus
In the event of a drive failure (indicated by an amber light), replace the faulty drive with a new, compatible 3.5-inch SATA drive. Consult your SAS controller documentation for specific hot-swap procedures if applicable.
7. Veaotsing
7.1 Levinud probleemid ja lahendused
| probleem | Võimalik põhjus | Lahendus |
|---|---|---|
| Seade ei lülitu sisse | Power cords disconnected; Power supply failure | Check power cord connections; Test power outlets; Contact support if power supply is faulty. |
| Drives not detected by host | SAS cables disconnected; SAS controller issue; Incorrect configuration | Verify SAS cable connections; Check SAS controller status; Review SAS controller documentation for configuration. |
| Amber light on drive | Drive failure or predictive failure | Replace the faulty drive. Back up data if possible before replacement. |
| Ülekuumenemine | Poor ventilation; Fan failure | Ensure proper airflow in the rack; Check fan operation; Clean dust from vents. |
8. Tehnilised andmed
| Funktsioon | Detail |
|---|---|
| Toote mudeli number | AJ924A |
| Kaubamärk | Hewlett Packard |
| Vormitegur | 2U rack-paigaldatav |
| Drive Bays | 12 x 3.5 tolli |
| Supported Drive Interface | Serial ATA (SATA) |
| Hostiliides | Jadaühendusega SCSI (SAS) |
| Digital Storage Capacity (Max) | 12 TB (with 1TB drives, actual capacity depends on drives installed) |
| Toote mõõtmed | 4.13 x 2.35 x 3.85 tolli (10.49 x 5.97 x 9.78 cm) |
| Kauba kaal | 120 naela (54.43 kg) |
| Tootja | HP |
| ASIN | B001F4R2F6 |
| UPC | 884420366867 |
9. Garantii ja tugi
For detailed warranty information, please refer to the warranty document included with your product or visit the official Hewlett Packard support website. Technical support and service options are available through Hewlett Packard's customer service channels. Please have your product model number (AJ924A) and serial number ready when contacting support.
